Good quality nipple wrench, about the best I've seen. Well worth it.

I’ve used a multitude of products from various companies. Until now, I found the steel used in wrenches too soft and easily marred. This SlixShot
Wrench is made of high carbon steel. I’ll never need to buy another.

I bought a wrench at my local hardware store & it broke on my first use.

The SliX wrench is a wrench that will last my lifetime and beyond.

Cannot beat the quality anywhere else.

I have a half a dozen nipple wrenches for revolvers. This wrench is the best. The long shaft and top round section make it easy to remove and install revolver nipples. Other nipple wrenches and the combination tools are OK but I prefer one excellent tool to perform one job. This is it.

I purchased this wrench because of the quality of the steel and the craftsmanship. It’s worth every penny. I’m a mechanic and there’s a reason why we spend $50 on a single wrench. It’s about the quality of the steel and the craftsmanship of the tool. This nipple wrench from Slix is no different. When you’re working on an expensive firearm or an expensive vehicle you need to know the tool is going to hold up time after time. And that’s what this nipple wrench does.

Very solid wrench well thought out works well on all of my muzzleloading pistols and rifles

Works real good

I have not yet had an oppertunity to use the slix wrench, but i can tell right away that it is very well made, of the highest quality. I have been using other Slix products for years, and as always, i am delivered a fine product. I am sure the wrench will be no less.

Best darn nipple wrench on the market. The design is so similar to the old spinner lug wrench for flat tires makes it so simple and easy to remove the nipples for cleaning and reinserting. If you shoot cap and ball with slix shot nipples, you gotta get one of these things

I destroyed two other store bought nipple removal tools. When the Slix Wrench arrived you could tell it was quality made. Removed rusted on nipples with no problem or damage. Highly recommend.

Dear Sirs: From Midway U.S.A., I purchased a Uberti 1851 Colt Navy revolver and could not get two nipples out. So I ordered your Nipple Wrench.
After much effort I removed the two stuck nipples that had been installed in wet chambers at the factory and had rusted in place. You make a great
wrench and it is still in one piece, unlike the two wrenches I tried before I purchased yours! Thanks!

Great wrench, easier to use for tough stuck nipples. I was still unable to get some stuck nipple out and bent the edges of the wrench trying.

Still a great product and would highly recommend over almost all others I’ve tried



Reply from SliXprings:

Our nipple wrench is heat-treated to a Rockwell hardness of 48–52, which is sufficient for removing most stuck nipples. If the existing nipples are seized due to rust, corrosion, or overtightening, we strongly recommend applying a quality rust or thread penetrant and allowing it to soak for several days before trying again. As with any tool, using it beyond its intended limits can cause it to break.

My order came in on time, and was well packaged. The construction of the wrench itself feels sturdy. I have yet to use this on my Uberti Colt 1851 Navy. But I’m more than confident that this wrench will stand the test of time, and is a must have for anyone who wants to get into shooting black powder revolvers.

Excellent pistol nipple wrench. Fits snug and hardened steel doesn’t slip and deform

I've now purchased two of these wrenches. They are the finest wrench available for removing and replacing nipples/cones on cap and ball and muzzel loading rifles. The material is strong and the craftsmanship is top notch. I highly recommend this product.

This wrench fits the slixshot Pietta 1860 Army nipple perfectly. The product is very well made and the design makes it easy to spin the nipple in and out. Highly recommended.

First and last one I'll ever buy :)

Can never have too many nipple wrenches, this one is solid.

Products are great. Greatly reduced misfires, in fact non since installation of the new nipples. Hopefully will be able to get more for other pistols later.

I had no problems with it. removing factory nipples or other nipples either best thing It’s not made cheap like the other ones are and utube has videos of it sometimes being a pain in the ass removing nipples from the cylinder and if you reading reviews and shopping for a wrench then I bet 99.9% you having that same BS problem right now i know because I was experiencing it myself. But I got slix wrench!!! so thank you slix for making a tool that so far works… but the other cheap wrenches is garbage!! the only thing good about them is you get a nipple pick. But for your nipples.. Buy the slix wrench and have no regrets!

This wrench is great I used it 10 times fits perfect every time and the ends of wrench didn't turn or roll up this is awesome this wrench will be with my black powder revolvers as long as I live. Thanks for a great product.

Great tool - fits perfect, and very strong. Would buy again.

As an ex auto mechanic of 16 years, I can appreciate having the right tools to do the job right.
This tool fits on the nipple with no wobble and it engages the flats with very little free play.
This wrench fits like a glove.....that's why it will do the job right.
(Used on an older CVA 1860 Army Pistol, 44 cal.)

Easy to remove and install nipples on remington new model army revolver

Bought 3 sets for 2 Uberti and 1 Pietta fast shipping and all fit like a glove A++++++++